Designing quantum systems with the measurement speed and accuracy needed for quantum error correction using superconducting qubits requires iterative design and test informed by accuratemodels and characterization tools. We introduce a single protocol, with few prerequisite calibrations, which measures the dispersive shift, resonator linewidth, and drive power used in the dispersive readout of superconducting qubits. We find that the resonator linewidth is poorly controlled with a factor of 2 between the maximum and minimum measured values, and is likely to require focused attention in future quantum error correction experiments. We also introduce a protocol for measuring the readout system efficiency using the same power levels as are used in typical qubit readout, and without the need to measure the qubit coherence. We routinely run these protocols on chips with tens of qubits, driven by automation software with little human interaction. Using the extracted system parameters, we find that a model based on those parameters predicts the readout signal to noise ratio to within 10% over a device with 54 qubits.
Measurement is an essential component of quantum algorithms, and for superconducting qubits it is often the most error prone. Here, we demonstrate model-based readout optimization achievinglow measurement errors while avoiding detrimental side-effects. For simultaneous and mid-circuit measurements across 17 qubits, we observe 1.5% error per qubit with a 500ns end-to-end duration and minimal excess reset error from residual resonator photons. We also suppress measurement-induced state transitions achieving a leakage rate limited by natural heating. This technique can scale to hundreds of qubits and be used to enhance the performance of error-correcting codes and near-term applications.
Superconducting qubits typically use a dispersive readout scheme, where a resonator is coupled to a qubit such that its frequency is qubit-state dependent. Measurement is performedby driving the resonator, where the transmitted resonator field yields information about the resonator frequency and thus the qubit state. Ideally, we could use arbitrarily strong resonator drives to achieve a target signal-to-noise ratio in the shortest possible time. However, experiments have shown that when the average resonator photon number exceeds a certain threshold, the qubit is excited out of its computational subspace, which we refer to as a measurement-induced state transition. These transitions degrade readout fidelity, and constitute leakage which precludes further operation of the qubit in, for example, error correction. Here we study these transitions using a transmon qubit by experimentally measuring their dependence on qubit frequency, average photon number, and qubit state, in the regime where the resonator frequency is lower than the qubit frequency. We observe signatures of resonant transitions between levels in the coupled qubit-resonator system that exhibit noisy behavior when measured repeatedly in time. We provide a semi-classical model of these transitions based on the rotating wave approximation and use it to predict the onset of state transitions in our experiments. Our results suggest the transmon is excited to levels near the top of its cosine potential following a state transition, where the charge dispersion of higher transmon levels explains the observed noisy behavior of state transitions. Moreover, occupation in these higher energy levels poses a major challenge for fast qubit reset.
Currently available superconducting quantum processors with interconnected transmon qubits are noisy and prone to various errors. The errors can be attributed to sources such as openquantum system effects and spurious inter-qubit couplings (crosstalk). The ZZ-coupling between qubits in fixed frequency transmon architectures is always present and contributes to both coherent and incoherent crosstalk errors. Its suppression is therefore a key step towards enhancing the fidelity of quantum computation using transmons. Here we propose the use of dynamical decoupling to suppress the crosstalk, and demonstrate the success of this scheme through experiments performed on several IBM quantum cloud processors. We perform open quantum system simulations of the multi-qubit processors and find good agreement with all the experimental results. We analyze the performance of the protocol based on a simple analytical model and elucidate the importance of the qubit drive frequency in interpreting the results. In particular, we demonstrate that the XY4 dynamical decoupling sequence loses its universality if the drive frequency is not much larger than the system-bath coupling strength. Our work demonstrates that dynamical decoupling is an effective and practical way to suppress crosstalk and open system effects, thus paving the way towards high-fidelity logic gates in transmon-based quantum computers.
Quantum annealers require accurate control and optimized operation schemes to reduce noise levels, in order to eventually demonstrate a computational advantage over classical algorithms.We study a high coherence four-junction capacitively shunted flux qubit (CSFQ), using dispersive measurements to extract system parameters and model the device. We confirm the multi-level structure of the circuit model of our CSFQ by annealing it through small spectral gaps and observing quantum signatures of energy level crossings. Josephson junction asymmetry inherent to the device causes a deleterious nonlinear cross-talk when annealing the qubit. We implement a nonlinear annealing path to correct the asymmetry in-situ, resulting in a 50% improvement in the qubit performance. Our results demonstrate a low-level quantum control scheme which enhances the success probability of a quantum annealer.
We analyze analytically, semi-analytically, and numerically the operation of Cross-Resonance (CR) gate for superconducting qubits (transmons). We find that a relatively simple semi-analyticalmethod gives accurate results for the CNOT-equivalent gate duration and compensating single-qubit rotations. It also allows us to minimize the CNOT gate duration over the amplitude of the applied microwave drive and find dependence on the detuning between the qubits. However, full numerical simulations are needed to calculate intrinsic fidelity of the CR gate. We decompose numerical infidelity into contributions from various physical mechanisms, thus finding the intrinsic error budget. In particular, at small drive amplitudes the CR gate fidelity is limited by unitary imperfections, while at large amplitudes it is limited by leakage. The gate duration and fidelity are analyzed numerically as functions of the detuning between qubits, their coupling, drive frequency, relative duration of pulse ramps, and microwave crosstalk. Our results show that the CR gate can provide intrinsic infidelity of less than 10−3 when a simple pulse shape is used.
Many superconducting qubit systems use the dispersive interaction between the qubit and a coupled harmonic resonator to perform quantum state measurement. Previous works have foundthat such measurements can induce state transitions in the qubit if the number of photons in the resonator is too high. We investigate these transitions and find that they can push the qubit out of the two-level subspace. Furthermore, these transitions show resonant behavior as a function of photon number. We develop a theory for these observations based on level crossings within the Jaynes-Cummings ladder, with transitions mediated by terms in the Hamiltonian which are typically ignored by the rotating wave approximation. We confirm the theory by measuring the photon occupation of the resonator when transitions occur while varying the detuning between the qubit and resonator.
Using circuit QED, we consider the measurement of a superconducting transmon qubit via a coupled microwave resonator. For ideally dispersive coupling, ringing up the resonator producescoherent states with frequencies matched to transmon energy states. Realistic coupling is not ideally dispersive, however, so transmon-resonator energy levels hybridize into joint eigenstate ladders of the Jaynes-Cummings type. Previous work has shown that ringing up the resonator approximately respects this ladder structure to produce a coherent state in the eigenbasis (a dressed coherent state). We numerically investigate the validity of this coherent state approximation to find two primary deviations. First, resonator ring-up leaks small stray populations into eigenstate ladders corresponding to different transmon states. Second, within an eigenstate ladder the transmon nonlinearity shears the coherent state as it evolves. We then show that the next natural approximation for this sheared state in the eigenbasis is a dressed squeezed state, and derive simple evolution equations for such states using a hybrid phase-Fock-space description.
In modern circuit QED architectures, superconducting transmon qubits are measured via the state-dependent phase and amplitude shift of a microwave field leaking from a coupled resonator.Determining this shift requires integrating the field quadratures for a nonzero duration, which can permit unwanted concurrent evolution. Here we investigate such dynamical degradation of the measurement fidelity caused by a detuned neighboring qubit. We find that in realistic parameter regimes, where the qubit ensemble-dephasing rate is slower than the qubit-qubit detuning, the joint qubit-qubit eigenstates are better discriminated by measurement than the bare states. Furthermore, we show that when the resonator leaks much more slowly than the qubit-qubit detuning, the measurement tracks the joint eigenstates nearly adiabatically. However, the measurement process also causes rare quantum jumps between the eigenstates. The rate of these jumps becomes significant if the resonator decay is comparable to or faster than the qubit-qubit detuning, thus significantly degrading the measurement fidelity in a manner reminiscent of energy relaxation processes.