High-fidelity quantum non-demolition qubit measurement is critical to error correction and rapid qubit feedback in large-scale quantum computing. High-fidelity readout requires passinga short and strong pulse through the qubit’s readout resonator, which is then processed by a sufficiently high bandwidth, high saturation power, and quantum-limited amplifier. We have developed a design pipeline that combines time-domain simulation of the un-truncated device Hamiltonian, fabrication constraints, and maximization of saturation power. We have realized an amplifier based on a modified NIST tri-layer Nb fabrication suite which utilizes an array of 25 radio frequency Superconducting QUantum Interference Devices (rf SQUIDs) embedded within a low-Q resonator powered by a high-power voltage pump delivered via a diplexer on the signal port. We show that, despite the intensity of the pump, the device is quantum-efficient and capable of high-fidelity measurement limited by state transitions in the transmon. We present experimental data demonstrating up to -91.2 dBm input saturation power with 20 dB gain, up to 28 MHz instantaneous bandwidth, and phase-preserving qubit measurements with 62% quantum efficiency.
Increasing the fidelity of single-qubit gates requires a combination of faster pulses and increased qubit coherence. However, with resonant qubit drive via a capacitively coupled port,these two objectives are mutually contradictory, as higher qubit quality factor requires a weaker coupling, necessitating longer pulses for the same applied power. Increasing drive power, on the other hand, can heat the qubit’s environment and degrade coherence. In this work, by using the inherent non-linearity of the transmon qubit, we circumvent this issue by introducing a new parametric driving scheme to perform single-qubit control. Specifically, we achieve rapid gate speed by pumping the transmon’s native Kerr term at approximately one third of the qubit’s resonant frequency. Given that transmons typically operate within a fairly narrow range of anharmonicity, this technique is applicable to all transmons. In both theory and experiment, we show that the Rabi rate of the process is proportional to applied drive amplitude cubed, allowing for rapid gate speed with only modest increases in applied power. In addition, we demonstrate that filtering can be used to protect the qubit’s coherence while performing rapid gates, and present theoretical calculations indicating that decay due to multi-photon losses, even in very strongly coupled drive lines, will not limit qubit lifetime. We demonstrate π/2 pulses as short as tens of nanoseconds with fidelity as high as 99.7\%, limited by the modest coherence of our transmon. We also present calculations indicating that this technique could reduce cryostat heating for fast gates, a vital requirement for large-scale quantum computers.
Many proposals to scale quantum technology rely on modular or distributed designs where individual quantum processors, called nodes, are linked together to form one large multinodequantum computer (MNQC). One scalable method to construct an MNQC is using superconducting quantum systems with optical interconnects. However, a limiting factor of these machines will be internode gates, which may be two to three orders of magnitude noisier and slower than local operations. Surmounting the limitations of internode gates will require a range of techniques, including improvements in entanglement generation, the use of entanglement distillation, and optimized software and compilers, and it remains unclear how improvements to these components interact to affect overall system performance, what performance from each is required, or even how to quantify the performance of each. In this paper, we employ a `co-design‘ inspired approach to quantify overall MNQC performance in terms of hardware models of internode links, entanglement distillation, and local architecture. In the case of superconducting MNQCs with microwave-to-optical links, we uncover a tradeoff between entanglement generation and distillation that threatens to degrade performance. We show how to navigate this tradeoff, lay out how compilers should optimize between local and internode gates, and discuss when noisy quantum links have an advantage over purely classical links. Using these results, we introduce a roadmap for the realization of early MNQCs which illustrates potential improvements to the hardware and software of MNQCs and outlines criteria for evaluating the landscape, from progress in entanglement generation and quantum memory to dedicated algorithms such as distributed quantum phase estimation. While we focus on superconducting devices with optical interconnects, our approach is general across MNQC implementations.
Microwave photonic graph states provide a promising approach for robust quantum communication between remote superconducting chips using microwave photons. Recently, Besse et al. [Nat.Commun. 11, 4887 (2020)] demonstrated that 1D graph states can be generated using two transmon qubits. In this paper, we propose to use transmon qubits combined with other microwave devices to construct more complex graph states. Specifically, we consider 2D lattice and tree-like graph states. We compare the performance using fixed- versus tunable-frequency transmon qubits and also for different photonic qubit encodings. In each case, we estimate the fidelity of the resulting microwave graph state assuming current experimental parameters and identify the main factors that limit performance.
Josephson Parametric Amplifiers (JPA) are nonlinear devices that are used for quantum sensing and qubit readout in the microwave regime. While JPAs regularly operate in the quantumlimit, their gain saturates for very small (few photon) input power. In a previous work, we showed that the saturation power of JPAs is not limited by pump depletion, but instead by the high-order nonlinearity of Josephson junctions, the nonlinear circuit elements that enables amplification in JPAs. Here, we present a systematic study of the nonlinearities in JPAs, we show which nonlinearities limit the saturation power, and present a strategy for optimizing the circuit parameters for achieving the best possible JPA. For concreteness, we focus on JPAs that are constructed around a Josephson Ring Modulator (JRM). We show that by tuning the external and shunt inductors, we should be able to take the best experimentally available JPAs and improve their saturation power by ∼15 dB. Finally, we argue that our methods and qualitative results are applicable to a broad range of cavity based JPAs.