Significant progress has been made in building large-scale superconducting quantum processors based on flip-chip technology. In this work, we use the flip-chip technology to realizea modified transmon qubit, donated as the „flipmon“, whose large shunt capacitor is replaced by a vacuum-gap parallel plate capacitor. To further reduce the qubit footprint, we place one of the qubit pads and a single Josephson junction on the bottom chip and the other pad on the top chip which is galvanically connected with the single Josephson junction through an indium bump. The electric field participation ratio can arrive at nearly 53% in air when the vacuum-gap is about 5 microns, and thus potentially leading to a lower dielectric loss. The coherence times of the flipmons are measured in the range of 30-60 microseconds, which are comparable with that of traditional transmons with similar fabrication processes. The electric field simulation indicates that the metal-air interface’s participation ratio increases significantly and may dominate the qubit’s decoherence. This suggests that more careful surface treatment needs to be considered. No evidence shows that the indium bumps inside the flipmons cause significant decoherence. With well-designed geometry and good surface treatment, the coherence of the flipmons can be further improved.
By using the dry etching process of tantalum (Ta) film, we had obtained transmon qubit with the best lifetime (T1) 503 us, suggesting that the dry etching process can be adopted inthe following multi-qubit fabrication with Ta film. We also compared the relaxation and coherence times of transmons made with different materials (Ta, Nb and Al) with the same design and fabrication processes of Josephson junction, we found that samples prepared with Ta film had the best performance, followed by those with Al film and Nb film. We inferred that the reason for this difference was due to the different loss of oxide materials located at the metal-air interface.
High fidelity two-qubit gates are fundamental for scaling up the superconducting number. We use two qubits coupled via a frequency-tunable coupler which can adjust the coupling strength,and demonstrate the CZ gate using two different schemes, adiabatic and di-adiabatic methods. The Clifford based Randomized Benchmarking (RB) method is used to assess and optimize the CZ gate fidelity. The fidelity of adiabatic and di-adiabatic CZ gates are 99.53(8)% and 98.72(2)%, respectively. We also analyze the errors induced by the decoherence, which are 92% of total for adiabatic CZ gate and 46% of total for di-adiabatic CZ gates. The adiabatic scheme is robust against the operation error. But the di-adiabatic scheme is sensitive to the purity and operation errors. Comparing to 30 ns duration time of adiabatic CZ gate, the duration time of di-adiabatic CZ gate is 19 ns, revealing lower incoherence error rincoherent,Clfford = 0.0197(5) than r′incoherent,Clfford = 0.0223(3).
We propose a protocol to realize parametric control of two-qubit coupling, where the amplitude and phase are tuned by a longitudinal field. Based on the tunable Hamiltonian, we demonstratethe superadiabatic two-qubit quantum gate using superconducting quantum circuits. Our experimental results show that the state of qubits evolves adiabatically during the gate operation even though the processing time is close to the quantum limit. In addition, the quantum state transition is insensitive to the variation of control parameters, and the fidelity of a SWAP gate achieved 98.5%. This robust parametric two-qubit gate can alleviate the tension of frequency crowding for quantum computation with multiple qubits.
Berry curvature is an imaginary component of the quantum geometric tensor (QGT) and is well studied in many branches of modern physics; however, the quantum metric as a real componentof the QGT is less explored. Here, by using tunable superconducting circuits, we experimentally demonstrate two methods to directly measure the quantum metric tensor for characterizing the geometry and topology of underlying quantum states in parameter space. The first method is to probe the transition probability after a sudden quench, and the second one is to detect the excitation rate under weak periodic driving. Furthermore, based on quantum-metric and Berry-curvature measurements, we explore a topological phase transition in a simulated time-reversal-symmetric system, which is characterized by the Euler characteristic number instead of the Chern number. The work opens up a unique approach to explore the topology of quantum states with the QGT.