The measurement of a superconducting qubit is implemented by coupling it to a resonator. The common choice is transverse coupling, which, in the dispersive approximation, introducesan interaction term which enables the measurement. This cross-Kerr term provides a qubit-state dependent dispersive shift in the resonator frequency with the device parameters chosen carefully to get sufficient signal while minimizing Purcell decay of the qubit. We introduce a two-mode circuit, nicknamed quantromon, with two orthogonal modes implementing a qubit and a resonator. Unlike before, where the coupling term emerges as a perturbative expansion, the quantromon has intrinsic cross-Kerr coupling by design. Our experiments implemented in a hybrid 2D-3D cQED architecture demonstrate some unique features of the quantromon like weak dependence of the dispersive shift on the qubit-resonator detuning and intrinsic Purcell protection. In a tunable qubit-frequency device, we show that the dispersive shift (2χ/2π) changes by only 0.8 MHz while the qubit-resonator detuning (Δ/2π) is varied between 0.398 GHz – 3.288 GHz. We also demonstrate Purcell protection in a second device where we tune the orthogonality between the two modes. Finally, we demonstrate a single-shot readout fidelity of 98.3% without using a parametric amplifier which is comparable to the state-of-the-art and suggests a potential simplification of the measurement circuitry for scaling up quantum processors.
Implementing a precise measurement of the quantum state of a qubit is very critical for building a practical quantum processor as it plays an important role in state initializationand quantum error correction. While the transmon qubit has been the most commonly used design in small to medium-scale processors, the fluxonium qubit is emerging as a strong alternative with the potential for high-fidelity gate operation as a result of the high anharmonicity and high coherence achievable due to its unique design. Here, we explore the measurement characteristics of a tantalum-based high-coherence fluxonium qubit and demonstrate single-shot measurement fidelity (assignment fidelity) of 96.2% and 97.8% without and with the use of a Josephson Parametric Amplifier respectively. We study the back-action of the measurement photons on the qubit and measure a QND (repeatability) fidelity of 99.6%. We find that the measurement fidelity and QND nature are limited by state-mixing errors and our results suggest that a careful study of measurement-induced transitions in the fluxonium is needed to further optimize the readout performance.
Qubit coherence and gate fidelity are typically considered the two most important metrics for characterizing a quantum processor. An equally important metric is inter-qubit connectivityas it minimizes gate count and allows implementing algorithms efficiently with reduced error. However, inter-qubit connectivity in superconducting processors tends to be limited to nearest neighbour due to practical constraints in the physical realization. Here, we introduce a novel superconducting architecture that uses a ring resonator as a multi-path coupling element with the qubits uniformly distributed throughout its circumference. Our planar design provides significant enhancement in connectivity over state of the art superconducting processors without any additional fabrication complexity. We theoretically analyse the qubit connectivity and experimentally verify it in a device capable of supporting up to twelve qubits where each qubit can be connected to nine other qubits. Our concept is scalable, adaptable to other platforms and has the potential to significantly accelerate progress in quantum computing, annealing, simulations and error correction.
Existing scalable superconducting quantum processors have only nearest-neighbor coupling. This leads to reduced circuit depth, requiring large series of gates to perform an arbitraryunitary operation in such systems. Recently, multi-modal devices have been demonstrated as a promising candidate for small quantum processor units. Always on longitudinal coupling in such circuits leads to implementation of native high fidelity multi-qubit gates. We propose an architecture using such devices as building blocks for a highly connected larger quantum circuit. To demonstrate a quantum operation between such blocks, a standard transmon is coupled to the multi-modal circuit using a 3D bus cavity giving rise to small exchange interaction between the transmon and one of the modes. We study the cross resonance interaction in such systems and characterize the entangling operation as well as the unitary imperfections and cross-talk as a function of device parameters. Finally, we tune up the cross resonance drive to implement multi-qubit gates in this architecture.
We propose and demonstrate a frequency-multiplexed readout scheme in 3D cQED architecture. We use four transmon qubits coupled to individual rectangular cavities which are aperture-coupledto a common rectangular waveguide feedline. A coaxial to waveguide transformer at the other end of the feedline allows one to launch and collect the multiplexed signal. The reflected readout signal is amplified by an impedance engineered broadband parametric amplifier with 380 MHz of bandwidth. This provides us high fidelity single-shot readout of multiple qubits using compact microwave circuitry, an efficient way for scaling up to more qubits in 3D cQED.